So, based on this tutorial, I tried to create the surFABoard logo with illustrator. ![]() I know how to vectorize black and white raster images by Inkscape, but I did not know how to make a part of the photo image a vector image. SurFABoard logo design illustrator (vector software) I am going to try softwares other than fusion 360. I will practice, Practice and PRACTICE! Practice makes perfect. I know little about how to use Fusion 360 yet. I will 3D-print a box and will test the waterproofness of them in the near future. Furthermore, the double-sided tape would play the role of waterproofing. In that case, the groove may not be necessary. My friend also said that if the size gets bigger, I will have to use a rubber sheet. Then you will need to redesign 3D modeling to fit that O-ring size. It is necessary to decide the size of the box required for storing the electronics and selecting an O-ring size close to the size of the box. One of my friends told me that there was no big O-ring if I design a box big. I am going to observe the product to make use of design for modeling. Also, I do not know how much the wall thickness (strength) necessary for waterproofing is. Considering such as to offset convex portions will be necessary. Since the concave-convex parts are the same size at this time, the 3D printed concave-convex part will not be inserted successfully. Watertight enclosure 3d modelling: Fusion 360 format (.f3d) After modelling Since sufficient thickness is needed in the part where the groove is formed, I redesigned as follows. In this design, the wall thickness of the box became thick enough to be dug a groove, it takes time and material cost in 3D printing. The operation made a groove on the top of the box. "Extrude" it from the back side of the lid with the operation "Join." then Modify/Combine" with the box as "Target Body" the lid as "Tool Body" and "Keep Tools" Select the top of the box as the profile plane and "Create/Sketch" a groove profile on it. Then "Modify/Shell" the box and place a lid as a "New Body" on the top of the box. I used AutoDesk Fusion 360 for my box modelling.įirst, I drew a rectangle sketch on XY plane and extruded the profile plane. When the lid is placed on the box and pressure is applied, the O-ring will be crushed, and the waterproof will be achieved There is a convex part on the back side of the lid. There is a groove in the top of the box wall, and rubber-made O-ring is placed in it. Romans CAD Shoemaster CAD ICad3D+ ElitronCAD 2D Footwear great list is hereĪutoCAD Architecture Chief Architect TurboCAD BricsCAD ProgeCAD and etc.Īs a design of a watertight enclosure, I assume a box like an image shown below. Optitex‘s ODev, OPro and OSel programs Kaledo from Lectra Telestia Creator FashionCAD and etc. I wondered if there were any CAD for a particular purpose? I did some my homework. Now that I understand the reason there are specific industry-oriented CAD softwares. There was a tutorial to design a surfboard with Fusion 360, but It doesn't look easy enough. I didn't realize there are CAD tools specialized in designing a surfboard. I exported my design in STL format and opened in 3D printing slicer software(Simplify 3D). Then, I adjusted the rocker profile, too. I adjusted blue bezier points to match my surfboard. I added blue bezier points on the board profile at every 100 mm from the nose of the board. ![]() I can modify the surfboard profile freely by moving blue bezier points. ![]() I started the application and opened and chose the blank board, which is appropriate for the size I'm going to design. The length of the board was 2440 mm(96 inches), the maximum thickness of was 750 mm(29.5 inches), and the maximum width was 560 mm(22 inches). I do not have any knowledge about surfboard design, and I do not want my original design to ruin the final project, so I decided to copy my existing surfboard designįirst, I measured my board dimensions. Monthly subscription($45 / month) available There are other softwears and interfaces were pretty much the same. I used AKU Shaper from that software based on this great documentation. I chose a CAD software specialized for surfboard design. surfboard design with 3D software software Also, I designed 2D for the final project's original logo. I am planning to mill the surfboard to the 8th week (make something big) and intend to print the containers 3D in the 5th week. They are surfboards, waterproof containers, fins (optional). ) a possible final project, and post it on your class pageĪs a homework assignment this week, I modeled what I needed for the final project. model (raster, vector, 2D, 3D, render, animate, simulate.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |